RSC-2 remote control system 

General description

RSC-2 device allows the user for remote switching on and off electronic and electric devices using a key fob transmitter. Radio transmission used for communication between the key fob transmitter unit and the RSC-2 controller is completely safe thanks to the application of KeeLoq ® encrypted data transmission system developed by Microchip Technology Inc. In terms of external design and dimensions, it corresponds exactly to commonly used relays: HFV4, HFV7A made by Hogfa, GRL-S-112D made by Goodsky, or the following models made by Bosch Minirelays: 332 019 103, 0 332 019 110, 0 332 019 109, 0 332 209 150, 0 332 209 138.

In order to fit the RSC-2 controller, standard relay sockets installed in cars can be used for the aforesaid relays. RSC-2 is a small but extremely functional device, containing two radio-controlled channels, which can operate in either dependent or independent mode, according to the software version.RSC-2 controllers may co-work (as executive components) with other controlling/signaling units. Primary functions of RSC-2

1. KeeLoq ® Dynamic code hopping technology made by Microchip Technology Inc.
2. Two channels working in either independent mode RSC-2e or dependent mode RSC-2d and RSC-2f.
3. Saving operating conditions of channels, configuration and logged key fob transmitters in EEPROM memory after disconnecting the power supply (up to 10 years).
4. Simple and convenient system configuration using a K-2 programmer.
5. Possibility to set a channel into monostable mode with timing adjustable from 0.2 to about 600 seconds.
6. Signaling the registration of the last (6th) key fob transmitter in EEPROM memory.
7. Independent (reset) switch-off of a channel/channels using a 3-button key fob transmitter (e.g. Banan).
8. Channel outputs with overcharging and thermal protection.
   
9. Possibility to connect inductive devices, e.g. relays.
   
10. Controlling the negative power supply (open collector output).

RSC-2e - remote controller with two independent channels. Press the Main push-button of the key fob transmitter to switch on/off the negative power supply on channel 1.

RSC-6 Remote Control System

General description

RSC-6 device allows the user for remote switching on and off electronic and electric devices using a key fob transmitter. Radio transmission used for communication between the key fob transmitter unit and the RSC-6 controller is completely safe thanks to the application of KeeLoq ® encrypted data transmission system developed by Microchip Technology Inc. In terms of external design and dimensions,
it corresponds exactly to commonly used relays: HFV4, HFV7A made by Hogfa, GRL-S-112D made by Goodsky, or the following models made by Bosch Minirelays: 332 019 103, 0 332 019 110, 0 332 019 109, 0 332 209 150, 0 332 209 138.
In order to fit the RSC-6 controller, standard relay sockets installed in cars can be used for the aforesaid relays. RSC-6 is a small but extremely functional device, containing two radio-controlled channels, which can operate in either dependent or independent mode, according to the software version.

Installation Notes

1. Mount out of sight in a location where it is not surrounded by metal, and where it is not exposed to the weather or to moisture. Metal will block the RF signal, resulting in a reduced range.
2. For best range, pull the antenna wire as long and straight as possible. If the receiver receives interference from local RF activity (e.g., an airport or military base), the antenna wire can be folded. DO NOT CUT THE ANTENNA WIRE.

Examples application

• Car Security  
  
• Garage doors
• Security systems home
• House Automatics
• Immobiliser remote control
• Garage Door Openers
• Remote-control switch for motor DC
• Parking Gate Operators
• remote control motorcycle
• Remote Lamp Switch - Home & Garden

RSC-6 controllers may co-work (as executive components) with other controlling/signaling units.

Primary functions of RSC-6

1. KeeLoq ® Dynamic code hopping technology made by Microchip Technology Inc.
2. One channel working in either independent mode RSC-6e or dependent mode RSC-6d and RSC-6f.
3. Saving operating conditions of channels, configuration and logged key fob transmitters in EEPROM
4. memory after disconnecting the power supply (up to 10 years).
5. Simple and convenient system configuration using a K-6 programmer.
6. Possibility to set a channel into monostable mode with timing adjustable from 0.2 to about 600 seconds.
7. Signaling the registration of the last (6th) key fob transmitter in EEPROM memory.
8. Independent (reset) switch-off of a channel using a 3-button key fob transmitter (e.g. Banan).
9. Channel outputs with overcharging and thermal protection.
   
10. Controlling the internal relay (carrying current 20 A).Versions of the RSC-6 radio controller

RSC-6d - remote controller with one dependent channel.
Press the Main push-button of the key fob transmitter to switch on channel 1 contacts: 87 and 30 connected) Press the Functional push-button of the key fob transmitter to switch off channel 1 contacts: 87 and 30 no connected)

RSC-6e - remote controller with one independent channel.
Press the Main push-button of the key fob transmitter to switch on channel 1(contacts: 87 and 30 connected). Press the Main push-button of the key fob transmitter to switch off channel 1(contacts: 87 and 30 no connected).

RSC-6f - remote controller with one dependent channel.
Press the Functional push-button of the key fob transmitter to switch on channel 1 (contacts: 87 and 30 connected) Press the Assistant push-button of the key fob transmitter to switch off channel 1 (contacts: 87and 30 no connected)

The Main push-button of the key fob transmitter you can be used for the controll car alarm system made by CORADO.